Catalina - Capri - 25s International Assocaition Logo(2006)  
Assn Members Area · Join
Association Forum
Association Forum
Home | Profile | Register | Active Topics | Forum Users | Search | FAQ
Username:
Password:
Save Password
Forgot your Password?

 All Forums
 Catalina/Capri 25/250 Sailor's Forums
 Catalina 250 Specific Forum
 #&*%! Centerboard Cable!
 New Topic  Topic Locked
 Printer Friendly
Author Previous Topic Topic Next Topic  

Tray
Navigator

Member Avatar

Namibia
224 Posts

Initially Posted - 07/29/2002 :  17:09:41  Show Profile
I just had my centerboard cable replaced after the original snapped a few weeks ago, and on its THIRD use, the new one snapped! I pulled it up through the conduit, and it looks like it was snipped with cable cutters. I am furious. I've had the boat since November and have already snapped two cables. Is there a lemon law for boats?<img src=icon_smile_angry.gif border=0 align=middle>

Tray
C-250WB #554
"Weeny Bean"

Edited by - on

n/a
deleted

Members Avatar

125 Posts

Response Posted - 07/29/2002 :  17:23:51  Show Profile
Tray, sorry to hear about snapola,, When sailing, are you raising and lowering, and tinkering with the centerboard ? My 250 is a 95 and I've never had to replace it. I seldom trailer, and leave the boat at the dock. When I'm sailing I have the centerboard "set" at a mild back sweep and I NEVER move it. That's my solution, never to raise or lower, when I'm back at the dock I still don't play with it unless I happen to trailer, which is almost never....I like the lake. I'm happy to stay there. No racers will no doubt disagree because they are habitual tinkerers, not me. It sounds to me like the cable is either not firmly in the groove of the turning ball, or it is being pinched every time you trailer. Let's see what everybody else has to say!


Edited by - on
Go to Top of Page

Arlyn Stewart
Master Marine Consultant

Members Avatar

USA
2984 Posts

Response Posted - 07/29/2002 :  18:53:41  Show Profile
From other post, and residue evidence on the sheave.... the cable is being cut by the sheave that is above the board. This likely happens when the board is pushed up beyond the normally raised position.

Some have even raised their bunkboards to alleviate this problem. My initial cable on my very early jan '96 boat which saw lots of service...cratered a year ago. Then I ran the center board onto a rock...and sliced the cable in the process.

It may be possible....that the board is not centering in the trunk adequately..and when fully raised...the cable is pushed very hard against the outer edge of the sheave and slicing the cable.

As stated earlier, the best preventive is to not haul the center board too firmly to the top. Of course, if trailering...it does need to be raised fully...maybe those who raised their bunks have the right idea.

I had my board out for repairs this season...and when going back in, attempted to better center the board...but there is very little adjustment room on the brass blocks that hold the axle.

Arlyn C-250 W/B #224

Edited by - on
Go to Top of Page

mday
Navigator

Members Avatar

197 Posts

Response Posted - 07/29/2002 :  20:23:39  Show Profile
I keep my boat in the water, but I usually pull the centerboard full up up while in the slip at the marina. There's a 5' depth limit in the floating docks, so I usually let it halfway down until I'm well out in the lake and set up for sailing, then I keep it all the way down. Coming back into the marina, I pull the centerboard halfway up. All this means I'm pulling it up and down frequently, and, so far, haven't had any cable problems. I have worn out the roller the line rides on, though. I've also had the boat out on the trailer maybe 3 times in the last three years without having the cable damaged (that I know of).

Max Day
C250 WB 380
Lake Pleasant, AZ

Edited by - on
Go to Top of Page

Tray
Navigator

Members Avatar

Namibia
224 Posts

Response Posted - 07/30/2002 :  19:27:58  Show Profile
I have never trailered the boat. I never tinker with the centerboard, unless I'm motoring/anchoring in a shallow area. It is just baffling to me that a stainless steel cable would snap so soon.

My dealer has recommended replacing the cable with polyester-dacron line until he can get another cable from Catalina.

Tray
C-250WB #554
"Weeny Bean"

Edited by - on
Go to Top of Page

MarkTM
Navigator

Members Avatar

USA
178 Posts

Response Posted - 07/31/2002 :  10:32:41  Show Profile  Visit MarkTM's Homepage
Tray,

Given your infrequent use of the centerboard cable, I'm surprised you are having so much trouble. I am a frequent user of the cable in that I fully lift my cable after I enter the slip because I don't want the centerboard taking the strain of wave action in the marina. I fully lower it each time out and then pull it back up a bit to improve boat balance. I've had my boat for four years now and have never had a problem with the cable . . . knock on wood <img src=icon_smile.gif border=0 align=middle>

Arlyn has warned many times about the danger of fully retracting the board. I trust what he says but I keep forgetting to mark the line with a permanent marker so that I can stop just short of fully up to keep the cable from pinching. I agree that this is a good thing. My board is getting more difficult to raise and so I really torque it when it reaches the fully up position because I want to be sure it is up. Marking the line would eliminate this risky behavior.

Mark Melchior
C250wb "Lorelei" #384
[url="http://www.texassailor.com/"]<img src="http://www.texassailor.com/texas.gif " border=0>[/url]
<font size=1>(click flag to visit Central Texas Sailor)</font id=size1>

Edited by - on
Go to Top of Page

jfesi
Navigator

Members Avatar

USA
101 Posts

Response Posted - 07/31/2002 :  17:20:17  Show Profile
My boat is a '95 WB 250 which I keep on its trailer at the Chesapeake. I have never had a problem with the centerboard (knock on wood)except that it seems to be getting harder to lift. I'm not sure if that is due to the centerboard's age or mine. <img src=icon_smile.gif border=0 align=middle> I raise and lower it several times during each weekend of sailing. When anchoring out, I like to raise it to stop the thumping noise it makes from passing waves. It has always done this.

This past weekend I dove under the boat and felt along the cable and felt the sheaves. I didn't detect any worn places on the cable. I couldn't feel much of anything around the sheaves. The water was too murky to see anything.

When I retract the CB, I pull it up until it won't go any more. Is this dangerous? If I remove the small table top in the cabin interior, will I be able to see the board pivot? Is there any way to lubricate the underwater sheaves?

Fred Flemming
Pride of Macungie
1995 C250 WB, Hull 92
flemmifc@apci.com




Edited by - on
Go to Top of Page

mday
Navigator

Members Avatar

197 Posts

Response Posted - 08/01/2002 :  00:39:35  Show Profile
Tray,

You said:
<BLOCKQUOTE id=quote><font size=1 face="Verdana, Arial, Helvetica" id=quote>quote:<hr height=1 noshade id=quote>I have never trailered the boat. I never tinker with the centerboard, unless I'm motoring/anchoring in a shallow area. It is just baffling to me that a stainless steel cable would snap so soon.<hr height=1 noshade id=quote></BLOCKQUOTE id=quote></font id=quote><font face="Verdana, Arial, Helvetica" size=2 id=quote>

So does this mean you cable is getting cut while the centerboard is sitting there in the down position????? Sounds to me like you have some enemies! I think your cable really was cut! Piss anyone off lately that knows where your boat is?


Max Day
C250 WB 380
Lake Pleasant, AZ

Edited by - on
Go to Top of Page

Arlyn Stewart
Master Marine Consultant

Members Avatar

USA
2984 Posts

Response Posted - 08/03/2002 :  09:53:33  Show Profile
Fred, no...removing the table top does not give you access to the board.

Some of the things that will contribute to the drag of the center board retract are the block n tackle and turning ball. Check all of these for smooth operation. Ensure that the tackly doesn't have twist on the line. Mine was installed incorrectly by the factory with the twist shackle on top and this place the lower block at a bad angle for line entry to the block inducing twist in the line. The twist shackle should be on the bottom block.

Ths nickle plated wire block on top is subject to drag from its side plates..check it out and replace if necessary.

The turning ball on the bottom must spin freely.

Look at each part of the system as the problem may not be individual but collective drag.

Arlyn C-250 W/B #224

Edited by - on
Go to Top of Page

Arlyn Stewart
Master Marine Consultant

Members Avatar

USA
2984 Posts

Response Posted - 08/03/2002 :  10:06:12  Show Profile
There is another issue that hasn't been mentioned much about the cable...this related to the down position. Many of us run our boards in a raked aft position to balance the "Lead" or helm. In fact, Catalina at some point began installing a stop block on the board to keep the board from dropping vertical. Wish I could tell what hull number it started with...the date on the mod drawing is May 1997. Raking the center board aft, leaves tension of course on the line...and if the pivot connection to the board doesn't swivel enough...then it will force a bend in the cable at the swage. The newer cable shackle is designed to eliminate this problem but note that there is an up and down way to install it as it is releived in one direction. To install the shackle in the wrong direction would contribute to lack of ability of the shackle to rotate and result in stressing the cable.

Arlyn C-250 W/B #224

Edited by - Arlyn Stewart on 08/03/2002 14:47:36

Edited by - on
Go to Top of Page

Tray
Navigator

Members Avatar

Namibia
224 Posts

Response Posted - 08/04/2002 :  19:22:24  Show Profile
Max,

I don't think I've given anyone a reason to cut my cable. I get along with everyone in the marina, and we all keep an eye on each other's boats.

The cable snapped as I was pulling the board up. It did seem more difficult to raise than usual, but not so difficult as to snap a brand new cable. Maybe an alligator turtle bit it.<img src=icon_smile_wink.gif border=0 align=middle>

Tray
C-250WB #554
"Weeny Bean"

Edited by - on
Go to Top of Page

jfesi
Navigator

Members Avatar

USA
101 Posts

Response Posted - 08/11/2002 :  14:45:06  Show Profile
UGH, Not that I can add much more to what has already been said, but I would like to add my tale of horror and disbelief. I too have been the victim of "cable snap-ola". I keep my boat at dock and have only removed it once...to repair the cable. I keep the board 3/4 raised at dock and adjust it when departing my slip. Also I adjust it when on the hook to avoid the thumping swing noise it makes. I can't believe that this boat cable can't withstand this mild treatment.IF anything, it should be able to be moved up and down depending on what point of sail your on. Please Catalina give us WB's a break, the boat wasn't cheap. For the record they have no response other than, it was something I did. Right!


Edited by - on
Go to Top of Page

Ben - FL
Admiral

Members Avatar

880 Posts

Response Posted - 08/11/2002 :  15:00:58  Show Profile  Visit Ben - FL's Homepage
Hey Tray,

When I had my C-22 it needed a new cable before it got any worse and dropped the 500# swingkeel. I had a new one made up in about twenty minutes while I waited at a place called Indusco on Talyrand Ave.(close to the old Gator Bowl.) Cost was about thirty bucks if I'm not mistaken. They had the cable and pressed a new clevis onto it.

BTW, Is Weeny Bean still up at the St. Marys or did you get her moved yet?

Safe voyages,
Ben, FL s/v Chick-a-pea C250wk

Edited by - on
Go to Top of Page

Tray
Navigator

Members Avatar

Namibia
224 Posts

Response Posted - 09/03/2002 :  21:29:51  Show Profile
I have an update from my dealer. He says that Catalina will have a new cable soon made of some kind of dacron material. I hope to hear something soon.

I haven't had time to sail since early August anyway, but I sure would like to be able to get my boat on a trailer if some storm should threaten.

Tray
C-250WB #554
"Weeny Bean"

Edited by - on
Go to Top of Page
  Previous Topic Topic Next Topic  
 New Topic  Topic Locked
 Printer Friendly
Jump To:
Association Forum © since 1999 Catalina Capri 25s International Association Go To Top Of Page
Powered By: Snitz Forums 2000 Version 3.4.06
Notice: The advice given on this site is based upon individual or quoted experience, yours may differ.
The Officers, Staff and members of this site only provide information based upon the concept that anyone utilizing this information does so at their own risk and holds harmless all contributors to this site.